Thursday, August 11, 2016

C-Track


                
Product Details:

The hanging track range is ideal for environments where the works of art are changed frequently or where it is inappropriate to damage the wall surface.

C track is a small extrusion designed to be applied to the ceiling in environments where it is inappropriate to fix to the wall, and provides a stable point to hang artworks from using a variety of materials including transparent cord, stainless cable or stainless rod. The C track can be fixed to existing ceilings as a surface installation or attached prior to the application of drywall to achieve a completely flush finish.

 

  


 

 


 

·         Stainless Steel Rods provides the most rigid installation, can be supplied in silver or white and will support artworks up to 110 lbs (50 kg) per pair.

·         Stainless Steel Cable will provide the strongest flexible cable system and will support artworks up to 77 lbs (35 kg) per pair.


·         Perlon Cord is semi-transparent and blends with most surfaces and is the best choice for a discreet installation. Will support artworks up to 55 lbs (25kg) per pair.


·         *Each cable or rod requires a top block.*


·         *Screws not included due to different use scenarios*

All of these systems are compatible with the Ryman hanger range for a higher level of security.

 

Useful Tips and Guidelines:

Hanging artworks from the ceiling will never match the weight capacity of hanging from a wall. The C Track is slim and robust but its overall strength will be governed by the number of fixings into something solid. The track is delivered pre-drilled at 1' centers. However because ceiling support structures vary so much, we have designed this track with an internal countersink. This means that it’s easy to drill the track wherever you find a sound fixing point and know that the countersunk screw will sit snugly in the base of the track.

Bear in mind that when an artwork is hung away from the wall, it has a tendency to lean forward. With the goal of keeping the work as vertical as possible you should make your attachments as high on the rear of the frame as possible or even consider the option of fixing to the top edge of the frame.

If it becomes necessary to fix into the drywall then be sure to use ‘hollow core fixings’ to achieve the best hold. When done professionally, drywall can be capable of carrying up to 12 lbs.

Installation Instructions:

Drill the track so that the fixing points coincide with a joist or something solid as this will ensure a far higher load limit for the track than if fixed directly to the drywall. The inside of the track already has the countersink for the screws built in. You should fix the track as close to the wall as possible as this will help to mitigate ‘picture lean’. When installing more than one length of track, insert one of the pins (supplied) halfway into the small circular opening at the end of the track and use this pin to engage with the next section. This will ensure that all pieces of track are in good alignment.  Repeat this process until you reach the last section and trim to the correct length.

Hanging Your Artworks:

With Perlon cord, feed the cord through the top block and insert into the opening at one end of the track. With stainless cable, feed the cord through the top block and insert into the opening at one end of the track. With stainless rods, insert the top blocks into the opening at one end of the track and slide to the correct position. Then screw the rods into place from underneath.

Slide the appropriate barrel up the cord or rod from the bottom and tighten at the required height with the bolt heads facing toward you. It’s much easier to do this with the two lengths side by side so that the barrel heights match.

For artworks with cord on the back, just place the cord over the hook. If you are using the Small Ryman Hanger, hook it over the small bolt and discard the large one and vice versa for the Large Ryman Hanger. For maximum strength be sure to tighten both the bolt (using a screwdriver) and the grub screw (using an allen key). With the rods at the correct distance apart, the artwork is lifted into place so that the protruding boltheads engage with the Ryman plate on the back of the artwork.                                                 
For more information on the C-Track:
https://www.artdisplay.com/store/p/1782-Absolute-C-Track.aspx
https://www.pinterest.com/liveartloud/museums-and-galleries/
https://www.pinterest.com/liveartloud/wall-mounted-art/

                                                      

No comments:

Post a Comment